Download Article

Download Article

PUR has multiple products bachelor for filtering h2o, but the filters become less constructive over time as they fill with contaminants. How y'all replace the filter depends on which system y'all're using. If you have a plastic bullpen or dispenser you keep in the refrigerator, soak the new filter before screwing information technology in. For filtration systems that attach to your sink faucet, just remove the quondam filter so yous can put the new one in its place. When you're finished, you'll take clean h2o to drink for some other few months!

  1. 1

    Soak the replacement filter in common cold water for xv minutes. Place the new filter in a make clean container that's deep enough and so you can fully submerge information technology. Fill the container with common cold water and leave it alone for at least 15 minutes. During this time, any excess carbon from the filter will lift out and separate so it doesn't go far your drinking water.[i]

    • Soaking the filter too ensures that h2o flows evenly when you lot use it.
    • Don't use h2o warmer than 86 °F (thirty °C) since it could damage the filter.

    Warning: Avoid using third-party filters with your PUR pitcher or dispenser since they may not fit as well or have been tested as efficiently.

  2. two

    Twist the old filter counterclockwise to remove it. Take the lid off of the pitcher or dispenser and set information technology aside. So, lift up the pour tray, which is the bluish plastic reservoir on summit, and take information technology out. Take hold of the cylindrical filter from the bottom and rotate information technology counterclockwise then it unhooks from the filter. Pull the old filter out through the top of the pour tray and throw in the garbage.[2]

    • Await until the pour tray is empty to alter your filter, or else it may exist hard to remove or you may spill.

    Advertisement

  3. iii

    Rinse the new filter nether your faucet for 10 seconds. Have the filter out of the container when it'due south finished soaking and hold information technology underneath your faucet. Turn on common cold water and rotate the filter and so you can rinse it off completely. Later on 10 seconds, turn off the h2o and milkshake out whatever excess that's notwithstanding in the filter.[3]

    • Don't use hot water to rinse the filter off, or else you may harm information technology.

  4. four

    Screw the filter clockwise into the cascade tray to secure it. Slide the long, cylindrical office of the filter through the hole in the middle of the pour tray and push it downwards every bit far as it goes. Hold the filter by the lesser and rotate it clockwise until yous hear information technology click into place. Attempt tapping on the end of the filter to make sure it doesn't popular out from the pour tray. Place the pour tray dorsum into the pitcher or dispenser earlier replacing the chapeau.[4]

    • If the filter does pop out of the cascade tray, then you didn't properly secure information technology. Reinsert it and effort turning it clockwise again.
    • PUR filters for pitchers and dispensers normally piece of work for 40 gallons (150 Fifty), or approximately 2 months.

  5. five

    Hold the Reset push down for 5 seconds if your pitcher or dispenser has ane. Some newer PUR pitchers and dispensers take sensors that detect when y'all need to replace the filter. Right after yous replace the filter, press the Reset button on the hat and keep it held down for 5 seconds. A green light will blink on the hat once the sensor resets.[five]

    • Older pitchers or dispensers may not take an electronic display.

    Ad

  1. 1

    Unscrew the filtration system from your faucet. Support the weight of the filtration system with your nondominant mitt so it doesn't fall and suspension. Rotate the plastic locking nut holding the filtration system to the faucet counterclockwise to loosen it. One time you unscrew the system completely, carefully lift it away from the faucet and set information technology down on a countertop or towel.[6]

    • Water may spill out from the faucet when you unscrew the filtration system.
    • Some models of PUR filtration systems may snap onto the faucet. If it doesn't unscrew, try pulling information technology straight downward from the faucet.

  2. two

    Twist open the top cover of the organisation to remove the old filter. Hold the filtration system so the rounded stop of the big cylinder points up. Unscrew the top from the cylinder by rotating it counterclockwise, and fix the cover bated. Pull the quondam filter straight out from the organisation and throw it away in your trash.[7]

    • The top cover is always on the opposite end of the spout that dispenses water.

  3. 3

    Fix the new filter inside of the system and spiral on the cover. Make sure the narrower end of the filter is on the bottom and the logo is right-side up. Place the filter into the filtration arrangement so it has a loose fit. Fix the top encompass back over the filter and screw it into place to secure it.[8]

  4. four

    Reattach the filtration system to your faucet. Hold the filtration organization against the bottom of the faucet so the threadings are perfectly horizontal, or else they won't grade a tight seal. Rotate the locking nut clockwise onto the faucet and continue tightening it until it's hand-tight. Turn on the h2o and brand sure information technology doesn't drip or leak at the seam.[9]

    • If your filtration system doesn't screw on, line it upwardly with the faucet and apply house pressure level to snap information technology on.

  5. five

    Run common cold h2o through the filtration system for 5 minutes. Turn the handle on the right side of the filtration organization to divert the water through the filter. Allow the water to run through the filter for 5 minutes to get rid of any residue within and so it works more efficiently. Afterwards that, you can use the filter immediately subsequently turning it on.[10]

    • PUR faucet filters piece of work for 100 gallons (380 Fifty) of water, or about 3 months of utilise.
    • Don't run water over 100 °F (38 °C) through the filter since you could impairment it.

    Warning: The water may sputter or look cloudy when you first use the new filter, merely it will become better as yous run water through it.

    Advertisement

Ask a Question

200 characters left

Include your email accost to get a bulletin when this question is answered.

Submit

Advertising

  • Many PUR filtration systems have electronic lights that notice when you need to change your filter. If yous come across a green light flash, you lot don't need to change your filter. If it blinks yellowish or blood-red, then you need to replace the filter soon.[xi]

Cheers for submitting a tip for review!

Advertisement

  • Don't use water that'south above 82 °F (28 °C) in a pitcher or over 100 °F (38 °C) through a faucet since it can damage the filter.[12]

  • Only employ the filter with water that's already safety to drink since it will non remove bacteria or infection.[xiii]

Advertisement

References

About This Commodity

Thanks to all authors for creating a page that has been read 41,096 times.

Did this article help you?